Kepco MST 488 Programmer Manuale Utente Scaricare il pdf (Pagina 10)

MST488-27 SVC 013004

TABLE OF CONTENTS

SECTION PAGE

APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS

A.1 Introduction ............................................................................................................................................. A-1

A.2 *CLS — Clear Status Command .......................................................................................................... A-1

A.3 *ESE — Standard Event Status Enable Command................................................................................ A-1

A.4 *ESE? — Standard Event Status Enable Query..................................................................................... A-1

A.5 *ESR? — Event Status Register Query................................................................................................. A-2

A.6 *IDN? — Identification Query.................................................................................................................. A-2

A.7 *OPC — Operation Complete Command ............................................................................................... A-2

A.8 *OPC? — Operation Complete Query .................................................................................................... A-3

A.9 *OPT? — Options Query ........................................................................................................................ A-3

A.10 *RST — Reset Command....................................................................................................................... A-4

A.11 *SRE — Service Request Enable Command ........................................................................................ A-4

A.12 *SRE? — Service Request Enable Query.............................................................................................. A-4

A.13 *STB? — Status Byte Register Query ................................................................................................... A-4

A.14 *TRG — Trigger Command ................................................................................................................... A-4

A.15 *TST? — Self Test Query....................................................................................................................... A-5

A.16 *WAI — Wait-to-Continue Command ..................................................................................................... A-5

APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS

B.1 Introduction ............................................................................................................................................. B-1

B.2

INITiate[:IMMediate] Command .............................................................................................. B-1

B.3

INITiate:CONTinuous

Command................................................................................................. B-1

B.4

INITiate:CONTinuous Query ....................................................................................................... B-2

B.5

INSTrument:CATalog Query.......................................................................................................... B-2

B.6

INSTrument[:NSELect]

Command .............................................................................................. B-2

B.7

INSTrument[:SELect]

Command ................................................................................................ B-2

B.8

INSTrument[:SELect]?

Query..................................................................................................... B-3

B.9

INSTrument:STATe

Command........................................................................................................ B-3

B.10

MEASure[:SCALar]:CURRent[:DC]?

Query............................................................................. B-3

B.11

MEASure[:VOLTage][:SCALar][:DC]?

Query ........................................................................ B-4

B.12

OUTPut[:STATe] Command............................................................................................................. B-4

B.13

OUTPut[:STATe] Query ................................................................................................................... B-4

B.14

[SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude]

Command........................... B-4

B.15

[SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude]

Query.................................. B-4

B.16

[SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude]

Command .............................. B-5

B.17

[SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude]?

Query .................................... B-5

B.18

[SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]

Command........................... B-6

B.19

[SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]?

Query ............................... B-6

B.20

[SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude]

Command................................ B-6

B.21

[SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude]?

Query .................................... B-6

B.22

[SOURce:]FUNCtion:MODE

Command ......................................................................................... B-7

B.23

STATus:OPERation:CONDition

Query....................................................................................... B-7

B.24

STATus:OPEReration:ENABle

Command .................................................................................. B-7

B.25

STATus:OPEReration:ENABle? Query....................................................................................... B-7

B.26

STATus:OPERation[:EVENt]

Query ........................................................................................... B-7

B.27

STATus:PRESet

Command............................................................................................................... B-7

B.28

STATus:QUEStionable[:EVENt]?

Query.................................................................................. B-8

B.29

STATus:QUEStionable:CONDition?

Query............................................................................. B-9

B.30

STATus:QUEStionable:ENABle

Command................................................................................ B-9

B.31

STATus:QUEStionable:ENABle?

Query .................................................................................... B-9

B.32

STATus:QUEStionable:INSTrument[1]?

Query ................................................................... B-9

B.33

STATus:QUEStionable:INSTrument2?

Query ........................................................................ B-9

B.34

STATus:QUEStionable:INSTrument[1]:ENABle

Command .............................................. B-10

B.35

STATus:QUEStionable:INSTrument[1]:ENABle

Query..................................................... B-10

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 67 68

Commenti su questo manuale

Nessun commento

Kepco MST 488 Programmer Manuale Utente Pagina 10

Commenti su questo manuale

Prodotti e manuali riguardandi Alimentatori elettrici Kepco MST 488 Programmer